24小时咨询热线
转弯输送机
皮带输送机
流水线
工作台
传送带
热风烘干炉
链板输送机
news
淄博皮带输送机安全操作流程:1、矿用皮带输送机应负载运行,运行正常后,即可放料,严禁先放料后运行;2、启动后,高速3~5min,检查各部位是否正常,传动带是否松动,方向偏差。如果有,调整从动辊两侧M20张紧地脚螺栓,调整后卡紧;3、严格控制机械设备的运输能力,严禁过载应用,导致构件过早损坏;4、检查主动辊。从动辊...
淄博不锈钢工作台清洗注意事项:1.一般来说,如果不锈钢工作台外观有灰尘和污垢,可以用弱洗涤剂等温水轻松清洗。如果工作台长时间不保养,工作台可能会损坏。2.用户可用温水或弱洗涤剂清洗,粘合剂成分用酒精或有机溶剂擦洗。假设不锈钢工作台的油、油、润滑油污染可以用软布清洗,然后用中性洗涤剂或氨溶液或专用洗涤剂清...
淄博皮带输送机安装方法简介:1、淄博皮带输送机机架的安装从头架开始,然后依次安装中间架和尾架。安装机架前,首先将中心线拉到输送机的总长度上。由于输送机的中心线一直保持在输送带正常运行的主要标准上,所以在安装每个机架时,一定要对准中心线,同时架子要找平。机架对中心线的允许误差为每米机长±0.1mm。但在输送...
淄博工作台如何正确维护?1、禁止用蒸汽消毒。2、定期进行性能检测,发现问题及时检修。3、淄博工作台使用一段时间后,随着过滤器上粉尘容量的增加,操作区域的气流速度逐渐降低。当不能满足使用要求时,取出预过滤器,拆下泡沫,用洗涤剂冲洗干净,晾干后放入框中使用。如果附件不干净或损坏,应更换。4、为防止未经高效过...
淄博皮带输送机常见问题及解决方法:1、电机不能启动或启动后立即变慢。故障原因分析:a路经故障;b工作电压降低;C直流接触器故障;d在1.5秒内不断实际操作。解决方法:检查路经,检查工作电压,检查负载家用电器,减少实际操作次数。2、电机发热;故障原因分析:由于超重、超长或输送带堵塞,运行压力扩大,电机负荷运行;...
淄博工作台设计要点:1、仪器不能在视觉死角部分配置。2、能保证操作人员在长时间作业时处于舒适的姿势。3、控制装置和显示装置的布置必须位于操作人员的正常工作空间范围内,如确保操作人员能够很好地观察显示装置,并确保操作人员能够操作所有控制装置。4、淄博工作台的高度应降低到坐姿人体视水平线以下,确保操作人员的...